Tile in Elm City, NC
Tile is the most durable surface you can put in a house, and also the least forgiving of a rushed job. A crooked layout, a thin spot in the mortar or a floor that flexes underneath will show up as lippage, hollow tiles or cracked grout. We install ceramic, porcelain, glass and natural stone tile on floors, in showers and on backsplashes, and we spend as much time on the layout and the base as on setting the tile itself. The result is a surface you do not have to think about. Professionally installed across Elm City.
Tile done right, the first time, in Elm City.
Homeowners across Elm City, NC call Southern Flooring Solutions for tile because every job runs with experienced installers, clear pricing, no surprise charges, and one number to call from first sample to finished floor.
We install tile across Elm City and the surrounding area, including Wilson, Rocky Mount, Lucama, Middlesex. Financing available over 60 months on qualifying installs.
What's included
- Ceramic, porcelain, glass and natural stone tile
- Floors, shower walls, tub surrounds and kitchen backsplashes
- Layout planned around the room's focal points and doorways
- Large-format and wood-look porcelain installed on a flat, prepared base
- First-quality product only, so extra tile can still be matched later
- Lifetime labor warranty on jobs sold at the initial in-home consultation
Built for Elm City homes.
Elm City was laid out in 1873 on a half-mile square of land along the Wilmington and Weldon Railroad and went by Toisnot for much of its early life. Much of the town is now a National Register district, full of frame houses and brick storefronts built between 1873 and 1930. Older homes like these deserve a careful hand. We bring samples to you and handle flooring in Elm City, NC with that in mind.
Elm City owes its existence to the railroad. In 1873 George Howard bought a half-mile square of land along the Wilmington and Weldon Railroad and sold off lots, and the railroad moved its depot from Joyner's to the new town. It was incorporated that December as Toisnot, after a swamp west of town. The name changed to Elm City in 1891, back to Toisnot in 1895, and to Elm City for good in 1913. The town sits in both Wilson and Nash counties, and the 2020 census counted 1,218 residents.
The Elm City Municipal Historic District was listed on the National Register in 1986. Its nomination describes a flat plain cut by the railroad, with roughly thirteen blocks and much of the property inside the town limits included. It has 85 contributing buildings, most built between 1873 and 1930. The Batts & Williams Store from 1884 is a three-story brick building, the tallest in town. The Elm City Bank, built in the 1920s, has a corner entrance with a tiled floor that spells out the bank's name. Most of the rest are frame houses and cottages along Main, Parker and Branch streets.
Frame houses of that age usually sit over a crawlspace, and the original floors are often still there under later carpet or vinyl. Our hardwood refinishing service can bring sound boards back to life. Floors that have settled for a century may need leveling, and thresholds between old rooms and later additions rarely line up. We look at all of that, and at the trim heights, before we price the job.
On a flat plain, water doesn't drain away quickly, and eastern North Carolina summers are humid. Moisture coming up from the crawlspace is the most common reason a wood floor cups. We check for a vapor barrier and give any new wood time to acclimate in the house before installing it. If the space under the house stays damp, engineered hardwood or luxury vinyl plank is the safer choice, and tile is a good fit for kitchens and baths.
Elm City is about an hour east of our Garner showroom, which is open by appointment. For a drive that long, our shop-at-home service makes more sense: we bring flooring and cabinet samples to your house and measure during the same visit.
Tile jobs near Elm City
Tile in Elm City, questions
Do you travel out to Elm City for estimates?
Yes. Our shop-at-home service brings samples to your house in Elm City, and we measure during the same visit. In-home estimates are available Monday through Friday, 9am to 3pm. If you'd like to see more products in person, our Garner showroom is open by appointment.
My old house has heart pine under the linoleum. Can it be saved?
Often it can. Heart pine is dense and holds up well, but old adhesive, nail holes and past damage vary from house to house. We'll check a section at the estimate. If the boards are sound, our hardwood refinishing service can sand and refinish them.
Can you redo the kitchen floor and cabinets in an older Elm City home?
Yes. We install kitchen cabinets, countertops and backsplash as well as flooring, and our in-house designer helps plan the layout. In older kitchens we check the floor for level first, since cabinets need a flat, solid base to sit right and doors need to hang true.
Ceramic or porcelain: what is the difference?
Both are fired clay. Porcelain is denser and absorbs less water, which makes it the better choice for floors, showers and anywhere it may freeze. Ceramic is a little softer and easier to cut, and it is a fine choice for walls and backsplashes. In practice, most floor tile we install today is porcelain, and ceramic shows up more often on walls.
Can tile go over a wood subfloor above a crawlspace?
Yes, but the floor has to be stiff enough. Tile and grout do not bend, so a subfloor that flexes when you walk on it will crack them. Over a crawlspace we check for bounce and soft spots and use the underlayment the tile and setting materials require. Large or natural stone tiles need an even stiffer floor than standard ceramic.
Is tile too cold or hard for a family room?
It is harder and cooler than wood or carpet, which some families love in a North Carolina summer and dislike on a January morning. Area rugs soften it in living spaces. If you like the look of wood but want tile's durability, wood-look porcelain plank is worth a look, and luxury vinyl plank is a softer alternative we can show you side by side.
Financing for 60 months
0% financing plans for 12, 24, 36, 48 and 60 months on approved credit. The 0% plans carry an additional cost, which we explain up front.
Every floor type we install in Elm City, NC
-
Elm CityKitchen & Bath Cabinets in Elm City
Kitchen cabinets and bathroom vanities in your sizes, finishes and hardware, planned with our in-house cabinetry designer.
Learn more → -
Elm CityCountertops in Elm City
Quartz, granite and other countertops for kitchens and baths, measured to your new cabinets and finished with a matching backsplash.
Learn more → -
Elm CityLuxury Vinyl Plank in Elm City
Waterproof luxury vinyl plank for kitchens, baths and busy main floors, with the wear layer and core matched to your household.
Learn more → -
Elm CityHardwood Flooring in Elm City
Solid and engineered hardwood chosen for your subfloor and installed for North Carolina humidity, so it stays flat and tight.
Learn more → -
Elm CityWaterproof Flooring in Elm City
Waterproof vinyl plank, water-resistant laminate and porcelain tile for kitchens, baths, laundry rooms and slab homes.
Learn more → -
Elm CityKitchen Remodeling in Elm City
Floors, cabinets, countertops and backsplash for your kitchen, chosen together and installed by one team, so every piece fits the one next to it.
Learn more →
Tile in nearby areas
Ready to start your Elm City project?
Book an in-home consultation and see samples in your own light. Lifetime labor warranty on jobs sold at the consultation.








